HEF Datasheet, HEF PDF, HEF Data sheet, HEF manual, HEF pdf, HEF, datenblatt, Electronics HEF, alldatasheet, free. 15 Apr Data sheet acquired from Harris Semiconductor. SCHSC − Revised October HCDB consists of an oscillator section and CMOS Stage Ripple-Carry Binary Counter/Divider and Oscillator. CMOS Stage Ripple-Carry Binary Counter/Divider and Oscillator – CDB. Datasheet.

Author: Morisar Taut
Country: Qatar
Language: English (Spanish)
Genre: Literature
Published (Last): 28 May 2011
Pages: 90
PDF File Size: 8.25 Mb
ePub File Size: 9.57 Mb
ISBN: 251-8-58150-557-6
Downloads: 25769
Price: Free* [*Free Regsitration Required]
Uploader: Mok

As usual, with such a one of project, I didn’t bother to create a PCB for the project.

When the second decade reaches 6 the output of IC10A will go low. This not only prevents the clock from advancing every minute during SET mode, it also starts counting a whole new minute once the clock is set to RUN mode again. IC4A divides the 1Hz pulse hef4060 datasheet IC2 also contains a 14 bit divider chain. From then on the flip-flop remains in that daatasheet, until the hours counter is reset to 0 again.

When the hours counter is reset, dataheet is hef4060 datasheet flip-flop, making its Q output high.

Access Denied

I have covered the time base and the counters here. This signal is fed to the datasheeet counter, as described below. While the clock is in SET mode there won’t come any carry pulses from the minutes counter and that signal is constantly high.

There’s one hef4060 datasheet we might use though. Navigation How to navigate Sponsors Please consider clicking on the Support Me hef4060 datasheet to show your appreciation.

Otherwise the roll over of the minutes counter would advance the hours counter too. These kind of capacitors usually have a black line on top of their body. It’s a bed side table clock, I don’t need it to light up the entire room at night, you know. We haven’t talked hef4060 datasheet the carry from the seconds counter to the minutes counter yet.


The CLK input to the flip-flop is low, because the hours counter has just been reset to 0. Next stop, hef4060 datasheet minutes counter. In Run mode only the SET button will have any effect, the other 3 buttons are inhibited. This page will describe sheet one in detail, while hef4060 datasheet next page will describe sheet number two.

HEF datasheet, HEF datasheets, manuals for HEF electornic semiconductor part

At the end it will produce an hef4060 datasheet frequency of 2Hz on output pin 3. I don’t need the output of the seconds counter itself, because I do hef4060 datasheet have a seconds display. This makes the output of IC10C constant low, except during the carry pulse. IC4B tries to do the same for the 0. On the next hef4060 datasheet I’ll explain the display circuit and power supply of the clock.

C5 hef4060 datasheet used to set the correct frequency. This will increase the stability of your clock. This allows you to advance the hours counter. Everything is built on pad board using Road Runner wiring to connect all the components together. This helps to tune the frequency of the time base to hef4060 datasheet correct value.

Therefore IC3A is used to divide the frequency down to 1Hz. The precision of the resistor value has no effect on the precision of the time base B. Now IC9D will inverse the pulses coming from the push button.

TP1 is a test point at which you can measure the buffered The other sheet covers the display circuit and the power supply.

Both inputs of IC10D hef4060 datasheet high when the button is pressed, making its output low. But when the most hef060 digit of the hours counter increments the clock input of the flip-flop rises, which sets the flip-flop, making the Q output low. We are only interested in two others, the Hz and the 64Hz outputs, which are used in the display section of hef4060 datasheet clock.

Related Articles (10)  JAK JSEM POTKAL RYBY PDF

CDB CMOS Stage Ripple-Carry Binary Counter/Divider and Oscillator |

However that would require one extra chip for just one gate, whereas I had a spare flip-flop available which could be ab used for datasehet same job. The Q output hef4060 datasheet be used by hef4060 datasheet display part of the circuit to suppress the leading 0 of the hours counter.

The output pulse from IC10A hef4006 goes out to the minutes counter, which has to be advanced at every overflow of the seconds counter. But this time hef4060 datasheet maximum count value is limited to This reset pulse is also used as carry hef4060 datasheet the hours counter.

When the clock is switched to SET mode though, the Hef4060 datasheet line goes low, which keeps the reset line he4060 the seconds counter constantly high, preventing the seconds counter to count. Once the counters reach that state they are reset back to 0 again.

CMOS 14-Stage Ripple-Carry Binary Counter/Divider and Oscillator

The clock can be in one of two different modes, in Run mode or in Set mode. It’s hef4060 datasheet Q0 of the first decade counter IC4A. This pulse is very short because its cause is removed by the reset almost instantly.